AZ31 Mg alloy plates with bimodal grain structures were fabricated via conventional extrusion under varying temperatures and speeds to investigate the mechanisms governing dynamic recrystallization(DRX)and texture evo...AZ31 Mg alloy plates with bimodal grain structures were fabricated via conventional extrusion under varying temperatures and speeds to investigate the mechanisms governing dynamic recrystallization(DRX)and texture evolution.Although all samples exhibited similar DRXed grain sizes(5.0–6.5μm)and fractions(76%–80%),they developed distinct c-axis orientations and mechanical properties.The P1 sample(350℃,0.1 mm/min)exhibited the lowest yield strength(∼192 MPa)but the highest elongation(∼18.2%),whereas the P3 sample(400℃,0.6 mm/min)showed the highest yield strength(∼241 MPa)and the lowest elongation(∼14.2%).The P2 sample(400℃,0.1 mm/min)demonstrated intermediate behavior(∼226 MPa,∼17.7%).These variations were primarily attributed to differences in c-axis orientations,particularly their alignment with respect to the normal direction(ND)and their slight deviation from the extrusion direction(ED).Microstructural analysis revealed that distinct DRX mechanisms were activated under different extrusion conditions.P1 predominantly exhibited twinning-induced dynamic recrystallization(TDRX)and continuous dynamic recrystallization(CDRX),whereas P3 primarily showed CDRX and discontinuous dynamic recrystallization(DDRX).These DRX mechanisms,in combination with the activated slip systems governed by the evolving local stress state,collectively contributed to orientation rotation and texture development.During the early stage of extrusion,tensile strain along the ED promoted basalslip,rotating the c-axes toward the ND.As deformation progressed,compressive strain along the ND became dominant.In P1,basalslip remained active,aligning the c-axes along the ND and forming a smaller angle with the ED.In contrast,P3 exhibited predominant pyramidal<c+a>slip,resulting in a pronounced deviation of the c-axes from the ND and a slightly larger angle relative to the ED.The P2 sample exhibited a transitional texture state between those of P1 and P3.展开更多
Carbon nanotubes（CNTs） reinforced Mg matrix composites were fabricated by a novel melt processing.The novel processing consisted of two courses：CNTs pre-dispersion and ultrasonic melt processing.Mechanical ball-mil...Carbon nanotubes（CNTs） reinforced Mg matrix composites were fabricated by a novel melt processing.The novel processing consisted of two courses：CNTs pre-dispersion and ultrasonic melt processing.Mechanical ball-milling was employed to pre-disperse CNTs on Zinc（Zn） flakes.Serious CNT entanglements were well dispersed to single CNT or tiny clusters on Zn flakes.The ultrasonic melt processing further dispersed CNTs in the Mg melt,especially tiny CNT clusters.Thus,a uniform dispersion of CNTs was achieved in the as-cast composites.Hot extrusion further improved the distribution of CNTs.CNTs increased both the strength and elongation of the matrix alloy.Notably,the elongation of the matrix alloy was enhanced by 40%.Grain refinement and the pulling-out of CNTs resulted in the evident improvement of ductility for the composites.展开更多
基金supported by National Key Research&Development Program of China(Grant no.2022YFE0110600)National Natural Science Foundation(Grant no.52220105003)+3 种基金the State Key Laboratory of Advanced Welding and Joining,Harbin Institute of Technology(Grant no.XNDCQQ2910201124)the National Natural Science Foundation for Young Scientists of China(Grant nos.51801042 and 51704088)Natural Science Foundation of Heilongjiang Province-Outstanding Youth Fund(Grant no.YQ2020E006)JSPS KAKENHI(Grant no.JP21H01669).
文摘AZ31 Mg alloy plates with bimodal grain structures were fabricated via conventional extrusion under varying temperatures and speeds to investigate the mechanisms governing dynamic recrystallization(DRX)and texture evolution.Although all samples exhibited similar DRXed grain sizes(5.0–6.5μm)and fractions(76%–80%),they developed distinct c-axis orientations and mechanical properties.The P1 sample(350℃,0.1 mm/min)exhibited the lowest yield strength(∼192 MPa)but the highest elongation(∼18.2%),whereas the P3 sample(400℃,0.6 mm/min)showed the highest yield strength(∼241 MPa)and the lowest elongation(∼14.2%).The P2 sample(400℃,0.1 mm/min)demonstrated intermediate behavior(∼226 MPa,∼17.7%).These variations were primarily attributed to differences in c-axis orientations,particularly their alignment with respect to the normal direction(ND)and their slight deviation from the extrusion direction(ED).Microstructural analysis revealed that distinct DRX mechanisms were activated under different extrusion conditions.P1 predominantly exhibited twinning-induced dynamic recrystallization(TDRX)and continuous dynamic recrystallization(CDRX),whereas P3 primarily showed CDRX and discontinuous dynamic recrystallization(DDRX).These DRX mechanisms,in combination with the activated slip systems governed by the evolving local stress state,collectively contributed to orientation rotation and texture development.During the early stage of extrusion,tensile strain along the ED promoted basalslip,rotating the c-axes toward the ND.As deformation progressed,compressive strain along the ND became dominant.In P1,basalslip remained active,aligning the c-axes along the ND and forming a smaller angle with the ED.In contrast,P3 exhibited predominant pyramidal<c+a>slip,resulting in a pronounced deviation of the c-axes from the ND and a slightly larger angle relative to the ED.The P2 sample exhibited a transitional texture state between those of P1 and P3.
基金supported by the National Natural Science Foundation of China(Grant No.51471059 and 51671066)the China Postdoctoral Science Foundation(Grant No.2014T70328)
文摘Carbon nanotubes（CNTs） reinforced Mg matrix composites were fabricated by a novel melt processing.The novel processing consisted of two courses：CNTs pre-dispersion and ultrasonic melt processing.Mechanical ball-milling was employed to pre-disperse CNTs on Zinc（Zn） flakes.Serious CNT entanglements were well dispersed to single CNT or tiny clusters on Zn flakes.The ultrasonic melt processing further dispersed CNTs in the Mg melt,especially tiny CNT clusters.Thus,a uniform dispersion of CNTs was achieved in the as-cast composites.Hot extrusion further improved the distribution of CNTs.CNTs increased both the strength and elongation of the matrix alloy.Notably,the elongation of the matrix alloy was enhanced by 40%.Grain refinement and the pulling-out of CNTs resulted in the evident improvement of ductility for the composites.
