The damping behavior of extruded Mg-xY(x=0.5,1.0,3.0 wt.%)sheets were investigated in detail concerning the effects of Y addition and temperature,and the relationship between damping capacity and yield strength was di...The damping behavior of extruded Mg-xY(x=0.5,1.0,3.0 wt.%)sheets were investigated in detail concerning the effects of Y addition and temperature,and the relationship between damping capacity and yield strength was discussed.At room temperature(RT),with Y content increasing from 0.5%to 3.0%,the damping capacity(Q-1)significantly decreased from 0.037 to 0.015.For all the studied sheets,the relationship between strain amplitude and Q-1 fitted well with the Granato and Liicke(G-L)dislocation damping model.With temperature increased,the G-L plots deviated from linearity indicating that the dislocation damping was not the only dominate mechanism,and the grain boundary sliding(GBS)could contribute to damping capacity.Consequently,the Q-1 increased remarkably above the critical temperature,and the critical temperature increased significantly from 50℃ to 290℃ with increasing Y contents from 0 to 3.0wt.%.This result implied that the segregation of Y solutes at grain boundary could depress the GBS,which was consistent with the recent finding of segregation tendency for rare-earth solutes.The extruded Mg-IY sheet exhibited slightly higher yield strength(Rp0.2)and Q-1 comparing with high-damping Mg-0.6Zr at RT.At an elevated temperature of 325℃,the Mg-IY sheet had similar Q-1 but over 3 times larger Rp0.2 than that of the pure Mg.The present study indicated that the extruded Mg-Y based alloys exhibited promising potential for developing high-performance damping alloys,especially for the elevated-temperature application.展开更多
In this study,a few Fe-based amorphous matrix composite coatings reinforced with various portions(4,8 and16 vol.%) of 31 6L stainless steel powders have been successfully produced through high velocity oxy-fuel(HVOF) ...In this study,a few Fe-based amorphous matrix composite coatings reinforced with various portions(4,8 and16 vol.%) of 31 6L stainless steel powders have been successfully produced through high velocity oxy-fuel(HVOF) spraying.The microstructure of the composite coatings was systematically characterized by X-ray diffraction(XRD),scanning electron microscopy(SEM) and transmission electron microscopy(TEM).The main structure of composite coatings remained amorphous while 31 6L stainless steel splats were distributed homogeneously in the amorphous matrix and well connected with surrounding amorphous phase.Bonding strength of coatings to the substrate was determined by 'pull-off' tensile tests.The results revealed that the31 6L stainless steel phase effectively improved the bonding strength of amorphous coatings,which is mainly contributed by the strong metallurgical bonding between stainless steel and amorphous splats.The addition of31 6L stainless steel also enhanced the ductility and fracture resistance of the coatings due to the ductile stainless steel phases,which can arrest crack propagation and increase energy dissipation.展开更多
In 2018,the STAR collaboration collected data from^(96)_(44)Ru+^(96)_(44)Ru and^(96)_(40)Zr+^(96)_(40)Zr at√^(S)NN=200 Ge V to search for the presence of the chiral magnetic effect in collisions of nuclei.The isobar ...In 2018,the STAR collaboration collected data from^(96)_(44)Ru+^(96)_(44)Ru and^(96)_(40)Zr+^(96)_(40)Zr at√^(S)NN=200 Ge V to search for the presence of the chiral magnetic effect in collisions of nuclei.The isobar collision species alternated frequently between 9644 Ru+^(96)_(44)Ru and^(96)_(40)Zr+^(96)_(40)Zr.In order to conduct blind analyses of studies related to the chiral magnetic effect in these isobar data,STAR developed a three-step blind analysis procedure.Analysts are initially provided a"reference sample"of data,comprised of a mix of events from the two species,the order of which respects time-dependent changes in run conditions.After tuning analysis codes and performing time-dependent quality assurance on the reference sample,analysts are provided a species-blind sample suitable for calculating efficiencies and corrections for individual≈30-min data-taking runs.For this sample,species-specific information is disguised,but individual output files contain data from a single isobar species.Only run-by-run corrections and code alteration subsequent to these corrections are allowed at this stage.Following these modifications,the"frozen"code is passed over the fully un-blind data,completing the blind analysis.As a check of the feasibility of the blind analysis procedure,analysts completed a"mock data challenge,"analyzing data from Au+Au collisions at√^(S)NN=27 Ge V,collected in 2018.The Au+Au data were prepared in the same manner intended for the isobar blind data.The details of the blind analysis procedure and results from the mock data challenge are presented.展开更多
Solid-state diffusion bonding is an advanced joining technique, which has been widely used to join similar or dissimilar materials. Generally, it is easy to observe the diffusion behavior during dissimilar bonding, bu...Solid-state diffusion bonding is an advanced joining technique, which has been widely used to join similar or dissimilar materials. Generally, it is easy to observe the diffusion behavior during dissimilar bonding, but for similar bonding the diffusion behavior has yet been observed via experiments. In this study, the diffusion behavior at void tip was firstly observed during similar bonding of stainless steel. Scanning electron microscopy with energy dispersive spectroscopy was used to examine the interface charac- teristic and diffusion behavior. The results showed that a diffusion region was discovered at void tip. Element concentrations of diffusion region were more than those of void region, but less than those of bonded region. This behavior indicated that the diffusion was ongoing at void tip, but the perfect bond has yet formed. The diffusion region was attributed to the interface diffusion from adjacent region to void tip due to the stress gradient along bonding interface. The mass accumulation at void tip transformed the sharp void tip into smooth one at the beginning of void shrinkage, and then resulted in shorter voids.展开更多
Full understanding of the thermomechanical behaviors of materials at high strain rates and high temperatures are of great importance from not only scientific meaning but also practical value in engineering structure d...Full understanding of the thermomechanical behaviors of materials at high strain rates and high temperatures are of great importance from not only scientific meaning but also practical value in engineering structure design and safety assessment.Great efforts have been made for abilities of operation the split Hopkinson bars,the most popular technique for experimental determination of mechanical behaviors of materials over the strain rates from 10^2 to 10^4 s^−1 over the past 70 years,at high temperatures since 1960s.A review of experiment work is presented in this paper to give an overview of the development of experimental techniques at high temperatures based on Hopkinson bar systems.The principles of the split Hopkinson bar requires the loading bars avoiding temperature gradient or keeping relatively low temperature when performing high temperature testing.Techniques such as performing temperature gradient corrections,rapid heating or using special designed automatically assembled systems were proposed by researchers to enable the operation of the split Hopkinson bars at temperature as high as possible.Moreover,to the application of high speed photographic technique for capturing the dynamic deformation process of the specimen in high temperature Hopkinson bar testing,some key issues of eliminating the strong thermal radiation induced lights oversaturation and de-blurring of images due to insufficient exposure at high temperature and high strain rate condition,as well as fabrication of high contrast speckle pattern for high temperature digital image correlation measurement were also proposed.The technique can now enable the split Hopkinson bar testing to be performed at high temperature up to 1873 K under the loading conditions of compression or tension with the in situ observation and full field measurement of deformation as well.The paper concludes with summaries of the most important achievements and highlighting of the prospects,trends and remaining challenges for future research.展开更多
The Lobster Eye Imager for Astronomy(LEIA),a pathfinder of the Wide-field X-ray Telescope of the Einstein Probe mission,was successfully launched onboard the SATech-01 satellite of the Chinese Academy of Sciences on20...The Lobster Eye Imager for Astronomy(LEIA),a pathfinder of the Wide-field X-ray Telescope of the Einstein Probe mission,was successfully launched onboard the SATech-01 satellite of the Chinese Academy of Sciences on2022 July 27.In this paper,we introduce the design and on-ground test results of the LEIA instrument.Using stateof-the-art Micro-Pore Optics(MPO),a wide field of view of 346 square degrees(18.6°×18.6°)of the X-ray imager is realized.An optical assembly composed of 36 MPO chips is used to focus incident X-ray photons,and four large-format complementary metal-oxide semiconductor(CMOS)sensors,each of size 6 cm×6 cm,are used as the focal plane detectors.The instrument has an angular resolution of 4’-8’(in terms of FWHM)for the central focal spot of the point-spread function,and an effective area of 2-3 cm^(2) at 1 keV in essentially all the directions within the field of view.The detection passband is 0.5-4 keV in soft X-rays and the sensitivity is2-3×10^(-11) erg s^(-1) cm^(-2)(about 1 milliCrab)with a 1000 s observation.The total weight of LEIA is 56 kg and the power is 85 W.The satellite,with a design lifetime of 2 yr,operates in a Sun-synchronous orbit of 500 km with an orbital period of 95 minutes.LEIA is paving the way for future missions by verifying in flight the technologies of both novel focusing imaging optics and CMOS sensors for X-ray observation,and by optimizing the working setups of the instrumental parameters.In addition,LEIA is able to carry out scientific observations to find new transients and to monitor known sources in the soft X-ray band,albeit with limited useful observing time available.展开更多
In this paper, a modelling benchmark exercise from the DECOVALEX-2011 project is presented. The bench- mark is based on the performance and results of a laboratory drying test and of the ventilation experiment （VE） ...In this paper, a modelling benchmark exercise from the DECOVALEX-2011 project is presented. The bench- mark is based on the performance and results of a laboratory drying test and of the ventilation experiment （VE） carried out in the Mont Terri Underground Rock Laboratory （URL）. Both tests involve Opalinus clay. The work aims at the identification, understanding and quantification of mechanisms taking place during the ventilation of a gallery in argillaceous host rocks on one hand and at investigating the capacity of different codes and individuals to reproduce these processes on the other hand. The 4-year in situ VE took place in a 1.3 m diameter unlined tunnel and included two resaturation-desaturation cycles. The test area was equipped with over one hundred sensors （including the global water mass balance of the system, relative humidity （RH）, water content, liquid pressure, relative displacement and concentration of some chemical species） to monitor the rock behaviour during ventilation. The laboratory drying experiment, carried out before the VE, was designed to mimic the in situ conditions. The work was organized in a progressive manner in terms of complexity of the computations to be performed, geared towards the full hydro-mechano-chemical （HMC） understanding of the VE, the final objective. The main results from the modelling work reported herein are that the response of the host rock to ventilation in argillaceous rocks is mainly governed by hydraulic processes （advective Darcy flow and non-advective vapour diffu- sion） and that the hydro-mechanical （TM） back coupling is weak. A ventilation experiment may thus be regarded as a large scale-long time pump test and it is used to determine the hydraulic conductivity of the rock mass.展开更多
Using the SG-III prototype laser at China Academy of Engineering Physics,Mianyang,we irradiated polystyrene(CH)samples with a thermal radiation drive,reaching conditions on the principal Hugoniot up to P≈1 TPa(10 Mba...Using the SG-III prototype laser at China Academy of Engineering Physics,Mianyang,we irradiated polystyrene(CH)samples with a thermal radiation drive,reaching conditions on the principal Hugoniot up to P≈1 TPa(10 Mbar),and away from the Hugoniot up to P≈300 GPa(3 Mbar).The response of each sample was measured with a velocity interferometry diagnostic to determine the material and shock velocity,and hence the conditions reached,and the reflectivity of the sample,from which changes in the conductivity can be inferred.By applying the selfimpedance mismatch technique with the measured velocities,the pressure and density of thermodynamic points away from the principal Hugoniot were determined.Our results show an unexpectedly large reflectivity at the highest shock pressures,while the off-Hugoniot points agree with previous work suggesting that shock-compressed CH conductivity is primarily temperature-dependent.展开更多
Assessment of mining impact on groundwater is one of critical considerations for longwall extension and sustainability,however usually constrained by limited data availability,hydrogeological variation,and the complex...Assessment of mining impact on groundwater is one of critical considerations for longwall extension and sustainability,however usually constrained by limited data availability,hydrogeological variation,and the complex coupled hydro-mechanical behaviour.This paper aims to determine the factors and mechanism of groundwater depressurisation and identify knowledge gaps and methodological limitations for improving groundwater impact assessment.Analysis of dewatering cases in Australian,Chinese,and US coalfields demonstrates that piezometric drawdown can further lead to surface hydrology degradation,while the hydraulic responses vary with longwall parameters and geological conditions.Statistical interpretation of 422 height of fracturing datasets indicates that the groundwater impact positively correlates to panel geometry and depth of cover,and more pronounced in panel interaction and top coal caving cases.In situ stress,rock competency,clay mineral infillings,fault,valley topography,and surface-subsurface water interaction are geological and hydrogeological factors influencing groundwater hydraulics and long-term recovery.The dewatering mechanism involves permeability enhancement and extensive flow through fracture networks,where interconnected fractures provide steep hydraulic gradients and smooth flow pathways draining the overlying water to goaf of lower heads.Future research should improve fracture network identification and interconnectivity quantification,accompanied by description of fuid flow dynamics in the high fracture frequency and large fracture aperture context.The paper recommends a research framework to address the knowledge gaps with continuous data collection and field-scale numerical modelling as key technical support.The paper consolidates the understanding of longwall mining impacting mine hydrology and provides viewpoints that facilitate an improved assessment ofgroundwaterdepressurisation.展开更多
To prolong the service lifetime of hot-section components used in marine environment at elevated tem-peratures,it is crucial to explore and develop high-temperature corrosion-resistant coatings.High-velocity oxygen fu...To prolong the service lifetime of hot-section components used in marine environment at elevated tem-peratures,it is crucial to explore and develop high-temperature corrosion-resistant coatings.High-velocity oxygen fuel(HVOF)sprayed NiCoCrAlY,Pt-modified NiCoCrAlY and pre-oxidized Pt-modified NiCoCrAlY coatings were prepared and investigated.This study is concerned with the performance of three coat-ings in a simulated marine environment based on the phase composition of corrosion products and mi-crostructure evolution of coating samples combined with first-principles density functional theory.The results show that the NiCoCrAlY coating was subject to accelerated corrosion and extensive aluminum depletion,leading to premature coating failure.The high-temperature corrosion resistance of Pt-modified NiCoCrAlY coating was found to be better than that of NiCoCrAlY coating.In contrast,the pre-oxidized Pt-modified NiCoCrAlY coating offered long-lasting protection and exhibited the best corrosion resistance,which is attributed to the positive synergistic effect between Pt modification and pre-oxidation.展开更多
This study aimed to investigate the erosion behavior and mechanism of a newly developed 25Cr3Mo2WNiV steel with a chrome coating using promoted ignition combustion tests.The erosion threshold pressure and temperature ...This study aimed to investigate the erosion behavior and mechanism of a newly developed 25Cr3Mo2WNiV steel with a chrome coating using promoted ignition combustion tests.The erosion threshold pressure and temperature of the chrome-coated 25Cr3Mo2WNiV steel were determined to be 0.2 MPa and 254.3 K higher than those of traditional chrome-coated 30SiMn2MoV steel.Furthermore,Kirkendall voids and inter-diffusion between the Cr coating and matrix were first observed before ero-sion.The improved erosion resistance of the chrome-coated 25Cr3Mo2WNiV steel was attributed to the suppression of the Kirkendall effect,which minimized heat generation at the Cr/matrix interface by pre-venting oxygen diffusion and reducing oxygen affinity.展开更多
We report an improved measurement of the neutrino mixing angle θ13 from the Daya Bay Reactor Neutrino Experiment. We exclude a zero value for sin22θ13 with a significance of 7.7 standard deviations. Electron antineu...We report an improved measurement of the neutrino mixing angle θ13 from the Daya Bay Reactor Neutrino Experiment. We exclude a zero value for sin22θ13 with a significance of 7.7 standard deviations. Electron antineutrinos from six reactors of 2.9 GWm th were detected in six antineutrino detectors deployed in two near （flux-weighted baselines of 470 m and 576 m） and one far （1648 m） underground experimental halls. Using 139 days of data, 28909 （205308） electron antineutrino candidates were detected at the far hall （near halls）. The ratio of the observed to the expected number of antineutrinos assuming no oscillations at the far hall is 0.944± 0.007（stat.） ± 0.003（syst.）. An analysis of the relative rates in six detectors finds sin22θ13=0.089± 0.010（stat.）±0.005（syst.） in a three-neutrino framework.展开更多
The cerebral blood flow（CBF） alterations related to sound-induced opening of the blood–brain barrier（BBB） in adult mice are studied using laser speckle contrast imaging（LSCI） and wavelet analysis of vascular ph...The cerebral blood flow（CBF） alterations related to sound-induced opening of the blood–brain barrier（BBB） in adult mice are studied using laser speckle contrast imaging（LSCI） and wavelet analysis of vascular physiology.The results clearly show that the opening of the BBB is accompanied by the changes of venous but not microvessel circulation in the brain. The elevation of the BBB permeability is associated with the decrease of venous CBF and the increase of its complexity. These data suggest that the cerebral veins rather than microvessels are sensitive components of the CBF related to the opening BBB.展开更多
High transverse momentum(pT)particle production is suppressed owing to the parton(jet)energy loss in the hot dense medium created in relativistic heavy-ion collisions.Redistribution of energy at low-to-modest pT has b...High transverse momentum(pT)particle production is suppressed owing to the parton(jet)energy loss in the hot dense medium created in relativistic heavy-ion collisions.Redistribution of energy at low-to-modest pT has been difficult to measure,owing to large anisotropic backgrounds.We report a data-driven method for background evaluation and subtraction,exploiting the away-side pseudorapidity gaps,to measure the jetlike correlation shape in Au+Au collisions at √sNN=200 GeV in the STAR experiment.The correlation shapes,for trigger particles pT>3GeV/c and various associated particle pT ranges within 0.5<pT<10GeV/c,are consistent with Gaussians,and their widths increase with centrality.The results indicate jet broadening in the medium created in central heavy-ion collisions.展开更多
The establishment of a possible connection between neutrino emission and gravitational-wave(GW)bursts is important to our understanding of the physical processes that occur when black holes or neutron stars merge.In t...The establishment of a possible connection between neutrino emission and gravitational-wave(GW)bursts is important to our understanding of the physical processes that occur when black holes or neutron stars merge.In the Daya Bay experiment,using the data collected from December 2011 to August 2017,a search was per-formed for electron-antineutrino signals that coincided with detected GW events,including GW150914,GW151012,GW151226,GW170104,GW170608,GW 170814,and GW 170817.We used three time windows of±10,±500,and±1000 s relative to the occurrence of the GW events and a neutrino energy range of 1.8 to 100 MeV to search for correlated neutrino candidates.The detected electron-antineutrino candidates were consistent with the expected background rates for all the three time windows.Assuming monochromatic spectra,we found upper limits(90%confidence level)of the electron-antineutrino fluence of(1.13-2.44)×10^(11)cm^(-2)at 5 MeV to 8.0×10^(7)cm^(-2)at 100 MeV for the three time w indows.Under the assumption of a Fermi-Dirac spectrum,the upper limits were found to be(5.4-7.0)×10^(9)cm^(2)for the three time windows.展开更多
A search for the rare decays W^(+)→D_(s)^(+)γ and Z→D0γis performed using proton-proton collision data collected by the LHCb experiment at a centre-of-mass energy of 13TeV,corresponding to an integrated luminosity...A search for the rare decays W^(+)→D_(s)^(+)γ and Z→D0γis performed using proton-proton collision data collected by the LHCb experiment at a centre-of-mass energy of 13TeV,corresponding to an integrated luminosity of 2.0fb−1.No significant signal is observed for either decay mode and upper limits on their branching fractions are set using W^(+)→D_(s)^(+)γ and Z→μ+μ−decays as normalization channels.The upper limits are 6.5×10^(−4) and 2.1×10^(−3) at 95% confidence level for the W^(+)→D_(s)^(+)γ and Z→D^(0)γ decay modes,respectively.This is the first reported search for the Z→D^(0)γ decay,while the upper limit on the W+→D+sγbranching fraction improves upon the previous best limit.展开更多
In June 2024,the world’s first full high temperature superconducting(HTS)tokamak has successfully achieved its first plasma operation in Shanghai,China[1].This tokamak device,HH70,is designed by Energy Singularity Fu...In June 2024,the world’s first full high temperature superconducting(HTS)tokamak has successfully achieved its first plasma operation in Shanghai,China[1].This tokamak device,HH70,is designed by Energy Singularity Fusion Power Technology(Shanghai)Ltd.(ES Company)in Shanghai,China.The conceptual and engineering design of HH70 was initiated in June 2022,whose major radius(R_(0))and minor radius(a)are 0.7-0.75 m and 0.25-0.31 m,respectively.Its toroidal magnetic field B_(0)at R_(0)=0.7 m is 0.6 T,the total inductance of the tor-oidal field(TF)magnet are 6.48 H.Over the past two years,ES company has achieved the first milestone:suc-cessfully design,construct and operate an HTS tokamak,and has amassed experience and know‐how about such a first‐of‐its‐kind HTS device.The HH70 tokamak’s magnet system consists of three types of coils:central solenoid(CS)coil,poloidal field(PF)coil,and toroidal field(TF)coil,in which all of the coils are fabricated by HTS conductors.Hence,the HH70 is currently the first tokamak in the world to be fully integrated with HTS coils,marking a groundbreaking advancement in fusion technology.展开更多
The prediction of reactor antineutrino spectra will play a crucial role as reactor experiments enter the precision era.The positron energy spectrum of 3.5 million antineutrino inverse beta decay reactions observed by ...The prediction of reactor antineutrino spectra will play a crucial role as reactor experiments enter the precision era.The positron energy spectrum of 3.5 million antineutrino inverse beta decay reactions observed by the Daya Bay experiment,in combination with the fission rates of fissile isotopes in the reactor,is used to extract the positron energy spectra resulting from the fission of specific isotopes.This information can be used to produce a precise,data-based prediction of the antineutrino energy spectrum in other reactor antineutrino experiments with different fission fractions than Daya Bay.The positron energy spectra are unfolded to obtain the antineutrino energy spectra by removing the contribution from detector response with the Wiener-SVD unfolding method.Consistent results are obtained with other unfolding methods.A technique to construct a data-based prediction of the reactor antineutrino energy spectrum is proposed and investigated.Given the reactor fission fractions,the technique can predict the energy spectrum to a 2%precision.In addition,we illustrate how to perform a rigorous comparison between the unfolded antineutrino spectrum and a theoretical model prediction that avoids the input model bias of the unfolding method.展开更多
We report the high-purity identification of cosmic-ray(CR)protons and a precise measurement of their energy spectrum from 0.15 to 12 PeV using the Large High Altitude Air Shower Observatory(LHAASO).Abundant event stat...We report the high-purity identification of cosmic-ray(CR)protons and a precise measurement of their energy spectrum from 0.15 to 12 PeV using the Large High Altitude Air Shower Observatory(LHAASO).Abundant event statistics,combined with the simultaneous detection of electrons/photons,muons,and Cherenkov light in air showers,enable spectroscopic measurements with statistical and systematic precision comparable to satellite data at lower energies.The proton spectrum shows significant hardening relative to low-energy extrapolations,culminating at 3 PeV,followed by sharp softening.This distinct spectral structure closely aligned with the knee in the all-particle spectrum points to the emergence of a new CR component at PeV energies that might be linked to the dozens of PeVatrons recently discovered by LHAASO,and offers crucial clues to the origin of Galactic cosmic rays.展开更多
基金This work was supported by National Natural Science Foundation of China(Nos.51401172 and 51601003)National University Student Innovation Experimental Project(No.201710613005)Sichuan Science and Technology Program(No.2019YJ0238).
文摘The damping behavior of extruded Mg-xY(x=0.5,1.0,3.0 wt.%)sheets were investigated in detail concerning the effects of Y addition and temperature,and the relationship between damping capacity and yield strength was discussed.At room temperature(RT),with Y content increasing from 0.5%to 3.0%,the damping capacity(Q-1)significantly decreased from 0.037 to 0.015.For all the studied sheets,the relationship between strain amplitude and Q-1 fitted well with the Granato and Liicke(G-L)dislocation damping model.With temperature increased,the G-L plots deviated from linearity indicating that the dislocation damping was not the only dominate mechanism,and the grain boundary sliding(GBS)could contribute to damping capacity.Consequently,the Q-1 increased remarkably above the critical temperature,and the critical temperature increased significantly from 50℃ to 290℃ with increasing Y contents from 0 to 3.0wt.%.This result implied that the segregation of Y solutes at grain boundary could depress the GBS,which was consistent with the recent finding of segregation tendency for rare-earth solutes.The extruded Mg-IY sheet exhibited slightly higher yield strength(Rp0.2)and Q-1 comparing with high-damping Mg-0.6Zr at RT.At an elevated temperature of 325℃,the Mg-IY sheet had similar Q-1 but over 3 times larger Rp0.2 than that of the pure Mg.The present study indicated that the extruded Mg-Y based alloys exhibited promising potential for developing high-performance damping alloys,especially for the elevated-temperature application.
基金financially supported by the National Natural Science Foundation of China (Grant Nos. 51271081 and 51301072)partially supported by the Key Fundamental Research Project from Shenzhen Research Council (No. JC201105170745A)
文摘In this study,a few Fe-based amorphous matrix composite coatings reinforced with various portions(4,8 and16 vol.%) of 31 6L stainless steel powders have been successfully produced through high velocity oxy-fuel(HVOF) spraying.The microstructure of the composite coatings was systematically characterized by X-ray diffraction(XRD),scanning electron microscopy(SEM) and transmission electron microscopy(TEM).The main structure of composite coatings remained amorphous while 31 6L stainless steel splats were distributed homogeneously in the amorphous matrix and well connected with surrounding amorphous phase.Bonding strength of coatings to the substrate was determined by 'pull-off' tensile tests.The results revealed that the31 6L stainless steel phase effectively improved the bonding strength of amorphous coatings,which is mainly contributed by the strong metallurgical bonding between stainless steel and amorphous splats.The addition of31 6L stainless steel also enhanced the ductility and fracture resistance of the coatings due to the ductile stainless steel phases,which can arrest crack propagation and increase energy dissipation.
文摘In 2018,the STAR collaboration collected data from^(96)_(44)Ru+^(96)_(44)Ru and^(96)_(40)Zr+^(96)_(40)Zr at√^(S)NN=200 Ge V to search for the presence of the chiral magnetic effect in collisions of nuclei.The isobar collision species alternated frequently between 9644 Ru+^(96)_(44)Ru and^(96)_(40)Zr+^(96)_(40)Zr.In order to conduct blind analyses of studies related to the chiral magnetic effect in these isobar data,STAR developed a three-step blind analysis procedure.Analysts are initially provided a"reference sample"of data,comprised of a mix of events from the two species,the order of which respects time-dependent changes in run conditions.After tuning analysis codes and performing time-dependent quality assurance on the reference sample,analysts are provided a species-blind sample suitable for calculating efficiencies and corrections for individual≈30-min data-taking runs.For this sample,species-specific information is disguised,but individual output files contain data from a single isobar species.Only run-by-run corrections and code alteration subsequent to these corrections are allowed at this stage.Following these modifications,the"frozen"code is passed over the fully un-blind data,completing the blind analysis.As a check of the feasibility of the blind analysis procedure,analysts completed a"mock data challenge,"analyzing data from Au+Au collisions at√^(S)NN=27 Ge V,collected in 2018.The Au+Au data were prepared in the same manner intended for the isobar blind data.The details of the blind analysis procedure and results from the mock data challenge are presented.
基金financially supported by the National Natural Science Foundation of China (Nos.51505386 and 51275416)the Fundamental Research funds for the Central Universities (No.3102017GX06003)
文摘Solid-state diffusion bonding is an advanced joining technique, which has been widely used to join similar or dissimilar materials. Generally, it is easy to observe the diffusion behavior during dissimilar bonding, but for similar bonding the diffusion behavior has yet been observed via experiments. In this study, the diffusion behavior at void tip was firstly observed during similar bonding of stainless steel. Scanning electron microscopy with energy dispersive spectroscopy was used to examine the interface charac- teristic and diffusion behavior. The results showed that a diffusion region was discovered at void tip. Element concentrations of diffusion region were more than those of void region, but less than those of bonded region. This behavior indicated that the diffusion was ongoing at void tip, but the perfect bond has yet formed. The diffusion region was attributed to the interface diffusion from adjacent region to void tip due to the stress gradient along bonding interface. The mass accumulation at void tip transformed the sharp void tip into smooth one at the beginning of void shrinkage, and then resulted in shorter voids.
基金This work is financially supported by the National Natural Science Foundation of China(Grants 11772268,11527803,11832015 and 11627901)the National Key R&D Program of China(Grant 2017YFB1103500)the 111 Project(Grant BP0719007).The authors also thanks for Dr.Yinggang Miao for useful discussions.
文摘Full understanding of the thermomechanical behaviors of materials at high strain rates and high temperatures are of great importance from not only scientific meaning but also practical value in engineering structure design and safety assessment.Great efforts have been made for abilities of operation the split Hopkinson bars,the most popular technique for experimental determination of mechanical behaviors of materials over the strain rates from 10^2 to 10^4 s^−1 over the past 70 years,at high temperatures since 1960s.A review of experiment work is presented in this paper to give an overview of the development of experimental techniques at high temperatures based on Hopkinson bar systems.The principles of the split Hopkinson bar requires the loading bars avoiding temperature gradient or keeping relatively low temperature when performing high temperature testing.Techniques such as performing temperature gradient corrections,rapid heating or using special designed automatically assembled systems were proposed by researchers to enable the operation of the split Hopkinson bars at temperature as high as possible.Moreover,to the application of high speed photographic technique for capturing the dynamic deformation process of the specimen in high temperature Hopkinson bar testing,some key issues of eliminating the strong thermal radiation induced lights oversaturation and de-blurring of images due to insufficient exposure at high temperature and high strain rate condition,as well as fabrication of high contrast speckle pattern for high temperature digital image correlation measurement were also proposed.The technique can now enable the split Hopkinson bar testing to be performed at high temperature up to 1873 K under the loading conditions of compression or tension with the in situ observation and full field measurement of deformation as well.The paper concludes with summaries of the most important achievements and highlighting of the prospects,trends and remaining challenges for future research.
基金supported by the Einstein Probe project,a mission in the Strategic Priority Program on Space Science of CAS(grant Nos.XDA15310000,XDA15052100)in part been supported by the European Union’s Horizon 2020 Program under the AHEAD2020 project(grant No.871158).
文摘The Lobster Eye Imager for Astronomy(LEIA),a pathfinder of the Wide-field X-ray Telescope of the Einstein Probe mission,was successfully launched onboard the SATech-01 satellite of the Chinese Academy of Sciences on2022 July 27.In this paper,we introduce the design and on-ground test results of the LEIA instrument.Using stateof-the-art Micro-Pore Optics(MPO),a wide field of view of 346 square degrees(18.6°×18.6°)of the X-ray imager is realized.An optical assembly composed of 36 MPO chips is used to focus incident X-ray photons,and four large-format complementary metal-oxide semiconductor(CMOS)sensors,each of size 6 cm×6 cm,are used as the focal plane detectors.The instrument has an angular resolution of 4’-8’(in terms of FWHM)for the central focal spot of the point-spread function,and an effective area of 2-3 cm^(2) at 1 keV in essentially all the directions within the field of view.The detection passband is 0.5-4 keV in soft X-rays and the sensitivity is2-3×10^(-11) erg s^(-1) cm^(-2)(about 1 milliCrab)with a 1000 s observation.The total weight of LEIA is 56 kg and the power is 85 W.The satellite,with a design lifetime of 2 yr,operates in a Sun-synchronous orbit of 500 km with an orbital period of 95 minutes.LEIA is paving the way for future missions by verifying in flight the technologies of both novel focusing imaging optics and CMOS sensors for X-ray observation,and by optimizing the working setups of the instrumental parameters.In addition,LEIA is able to carry out scientific observations to find new transients and to monitor known sources in the soft X-ray band,albeit with limited useful observing time available.
基金conducted within the context of the international DECOVALEX Projectthe Funding Organizations who supported the workthe EC project NF-PRO (Contract number FI6W-CT-2003-02389) under the coor-dination of ENRESA (Empresa Nacional de Residuos Radiactivos)
文摘In this paper, a modelling benchmark exercise from the DECOVALEX-2011 project is presented. The bench- mark is based on the performance and results of a laboratory drying test and of the ventilation experiment （VE） carried out in the Mont Terri Underground Rock Laboratory （URL）. Both tests involve Opalinus clay. The work aims at the identification, understanding and quantification of mechanisms taking place during the ventilation of a gallery in argillaceous host rocks on one hand and at investigating the capacity of different codes and individuals to reproduce these processes on the other hand. The 4-year in situ VE took place in a 1.3 m diameter unlined tunnel and included two resaturation-desaturation cycles. The test area was equipped with over one hundred sensors （including the global water mass balance of the system, relative humidity （RH）, water content, liquid pressure, relative displacement and concentration of some chemical species） to monitor the rock behaviour during ventilation. The laboratory drying experiment, carried out before the VE, was designed to mimic the in situ conditions. The work was organized in a progressive manner in terms of complexity of the computations to be performed, geared towards the full hydro-mechano-chemical （HMC） understanding of the VE, the final objective. The main results from the modelling work reported herein are that the response of the host rock to ventilation in argillaceous rocks is mainly governed by hydraulic processes （advective Darcy flow and non-advective vapour diffu- sion） and that the hydro-mechanical （TM） back coupling is weak. A ventilation experiment may thus be regarded as a large scale-long time pump test and it is used to determine the hydraulic conductivity of the rock mass.
基金The authors would like to thank the technical teams at LFRC for their invaluable work producing the targets and operating the facility.N.J.H.and D.K.were supported by the Helmholtz Association under Grant No.VH-NG-1141.Y.L.was supported by the National Natural Science Foundation of China(Grant No.11605189).
文摘Using the SG-III prototype laser at China Academy of Engineering Physics,Mianyang,we irradiated polystyrene(CH)samples with a thermal radiation drive,reaching conditions on the principal Hugoniot up to P≈1 TPa(10 Mbar),and away from the Hugoniot up to P≈300 GPa(3 Mbar).The response of each sample was measured with a velocity interferometry diagnostic to determine the material and shock velocity,and hence the conditions reached,and the reflectivity of the sample,from which changes in the conductivity can be inferred.By applying the selfimpedance mismatch technique with the measured velocities,the pressure and density of thermodynamic points away from the principal Hugoniot were determined.Our results show an unexpectedly large reflectivity at the highest shock pressures,while the off-Hugoniot points agree with previous work suggesting that shock-compressed CH conductivity is primarily temperature-dependent.
文摘Assessment of mining impact on groundwater is one of critical considerations for longwall extension and sustainability,however usually constrained by limited data availability,hydrogeological variation,and the complex coupled hydro-mechanical behaviour.This paper aims to determine the factors and mechanism of groundwater depressurisation and identify knowledge gaps and methodological limitations for improving groundwater impact assessment.Analysis of dewatering cases in Australian,Chinese,and US coalfields demonstrates that piezometric drawdown can further lead to surface hydrology degradation,while the hydraulic responses vary with longwall parameters and geological conditions.Statistical interpretation of 422 height of fracturing datasets indicates that the groundwater impact positively correlates to panel geometry and depth of cover,and more pronounced in panel interaction and top coal caving cases.In situ stress,rock competency,clay mineral infillings,fault,valley topography,and surface-subsurface water interaction are geological and hydrogeological factors influencing groundwater hydraulics and long-term recovery.The dewatering mechanism involves permeability enhancement and extensive flow through fracture networks,where interconnected fractures provide steep hydraulic gradients and smooth flow pathways draining the overlying water to goaf of lower heads.Future research should improve fracture network identification and interconnectivity quantification,accompanied by description of fuid flow dynamics in the high fracture frequency and large fracture aperture context.The paper recommends a research framework to address the knowledge gaps with continuous data collection and field-scale numerical modelling as key technical support.The paper consolidates the understanding of longwall mining impacting mine hydrology and provides viewpoints that facilitate an improved assessment ofgroundwaterdepressurisation.
基金supported by the National Science and Technology Major Project(No.J2019-IV-0006-0074)the Key Research Program of the Chinese Academy of Sciences(No.ZDRW-CN-2021-2-2)+2 种基金the National Natural Science Foundation of China(No.52301116)support by the Joint Funds of the National Natural Science Foundation of China(“Ye Qisun”Science Funds,No.U2241251)the Innovation Engineering Project(No.211-XXXX-N106-01).
文摘To prolong the service lifetime of hot-section components used in marine environment at elevated tem-peratures,it is crucial to explore and develop high-temperature corrosion-resistant coatings.High-velocity oxygen fuel(HVOF)sprayed NiCoCrAlY,Pt-modified NiCoCrAlY and pre-oxidized Pt-modified NiCoCrAlY coatings were prepared and investigated.This study is concerned with the performance of three coat-ings in a simulated marine environment based on the phase composition of corrosion products and mi-crostructure evolution of coating samples combined with first-principles density functional theory.The results show that the NiCoCrAlY coating was subject to accelerated corrosion and extensive aluminum depletion,leading to premature coating failure.The high-temperature corrosion resistance of Pt-modified NiCoCrAlY coating was found to be better than that of NiCoCrAlY coating.In contrast,the pre-oxidized Pt-modified NiCoCrAlY coating offered long-lasting protection and exhibited the best corrosion resistance,which is attributed to the positive synergistic effect between Pt modification and pre-oxidation.
基金Technology Fund of the Ministry of science and technology(No.2020-JCJQ-JJ-248)Fundamental Research Funds for the Central Universities(No.FRF-GF-20-21B)+1 种基金National Natural Science Foundation of China(No.52101072)The authors would like to express their gratitude for the experimental contributions and helpful suggestions from Dr.T.L.Sun.
文摘This study aimed to investigate the erosion behavior and mechanism of a newly developed 25Cr3Mo2WNiV steel with a chrome coating using promoted ignition combustion tests.The erosion threshold pressure and temperature of the chrome-coated 25Cr3Mo2WNiV steel were determined to be 0.2 MPa and 254.3 K higher than those of traditional chrome-coated 30SiMn2MoV steel.Furthermore,Kirkendall voids and inter-diffusion between the Cr coating and matrix were first observed before ero-sion.The improved erosion resistance of the chrome-coated 25Cr3Mo2WNiV steel was attributed to the suppression of the Kirkendall effect,which minimized heat generation at the Cr/matrix interface by pre-venting oxygen diffusion and reducing oxygen affinity.
基金Supported by the Ministry of Science and Technology of Chinathe United States Department of Energy+15 种基金the Chinese Academy of Sciencesthe National Natural Science Foundation of Chinathe Guangdong provincial governmentthe Shenzhen municipal governmentthe China Guangdong Nuclear Power GroupShanghai Laboratory for Particle Physics and Cosmologythe Research Grants Council of the Hong Kong Special Administrative Region of ChinaUniversity Development Fund of The University of Hong Kongthe MOE program for Research of Excellence at NTU, NCTUNSC fund support from Taipeithe U.S. National Science Foundationthe Alfred P. Sloan Foundationthe Ministry of EducationYouth and Sports of the Czech Republicthe Czech Science Foundationthe Joint Institute of Nuclear Research in Dubna,Russia
文摘We report an improved measurement of the neutrino mixing angle θ13 from the Daya Bay Reactor Neutrino Experiment. We exclude a zero value for sin22θ13 with a significance of 7.7 standard deviations. Electron antineutrinos from six reactors of 2.9 GWm th were detected in six antineutrino detectors deployed in two near （flux-weighted baselines of 470 m and 576 m） and one far （1648 m） underground experimental halls. Using 139 days of data, 28909 （205308） electron antineutrino candidates were detected at the far hall （near halls）. The ratio of the observed to the expected number of antineutrinos assuming no oscillations at the far hall is 0.944± 0.007（stat.） ± 0.003（syst.）. An analysis of the relative rates in six detectors finds sin22θ13=0.089± 0.010（stat.）±0.005（syst.） in a three-neutrino framework.
基金supported by the Grant of Russian Science Foundation No 17-15-01263supported by the Open Research Fund of Key Laboratory for Biomedical Photonics,HUST,Ministry of Education,China
文摘The cerebral blood flow（CBF） alterations related to sound-induced opening of the blood–brain barrier（BBB） in adult mice are studied using laser speckle contrast imaging（LSCI） and wavelet analysis of vascular physiology.The results clearly show that the opening of the BBB is accompanied by the changes of venous but not microvessel circulation in the brain. The elevation of the BBB permeability is associated with the decrease of venous CBF and the increase of its complexity. These data suggest that the cerebral veins rather than microvessels are sensitive components of the CBF related to the opening BBB.
文摘High transverse momentum(pT)particle production is suppressed owing to the parton(jet)energy loss in the hot dense medium created in relativistic heavy-ion collisions.Redistribution of energy at low-to-modest pT has been difficult to measure,owing to large anisotropic backgrounds.We report a data-driven method for background evaluation and subtraction,exploiting the away-side pseudorapidity gaps,to measure the jetlike correlation shape in Au+Au collisions at √sNN=200 GeV in the STAR experiment.The correlation shapes,for trigger particles pT>3GeV/c and various associated particle pT ranges within 0.5<pT<10GeV/c,are consistent with Gaussians,and their widths increase with centrality.The results indicate jet broadening in the medium created in central heavy-ion collisions.
基金Daya Bay is supported in part by the Ministry of Science and Technology o f China, the U.S. Department o f Energy, the Chinese Academy of Sciences, the CASCenter for Excellence in Particle Physics, the National Natural Science Foundation of China, the Guangdong provincial government, the Shenzhen municipal government,the China General Nuclear Power Group, Key Laboratory of Particle and Radiation Imaging (Tsinghua University), the Ministry of Education, Key Laboratory ofParticle Physics and Particle Irradiation (Shandong University), the Ministry o f Education, Shanghai Laboratory for Particle Physics and Cosmology, the ResearchGrants Council o f the Hong Kong Special Administrative Region of China, the University Development Fund of the University of Hong Kong, the MOE program forResearch of Excellence at National Taiwan University, National Chiao-Tung University, NSC fund support from Taiwan, the U.S. National Science Foundation, the AlfredP. Sloan Foundation, the Ministry o f Education, Youth, and Sports of the Czech Republic, the Charles University GAUK (284317), the Joint Institute o f NuclearResearch in Dubna, Russia, the National Commission of Scientific and Technological Research of Chile, and the Tsinghua University Initiative Scientific Research Program.
文摘The establishment of a possible connection between neutrino emission and gravitational-wave(GW)bursts is important to our understanding of the physical processes that occur when black holes or neutron stars merge.In the Daya Bay experiment,using the data collected from December 2011 to August 2017,a search was per-formed for electron-antineutrino signals that coincided with detected GW events,including GW150914,GW151012,GW151226,GW170104,GW170608,GW 170814,and GW 170817.We used three time windows of±10,±500,and±1000 s relative to the occurrence of the GW events and a neutrino energy range of 1.8 to 100 MeV to search for correlated neutrino candidates.The detected electron-antineutrino candidates were consistent with the expected background rates for all the three time windows.Assuming monochromatic spectra,we found upper limits(90%confidence level)of the electron-antineutrino fluence of(1.13-2.44)×10^(11)cm^(-2)at 5 MeV to 8.0×10^(7)cm^(-2)at 100 MeV for the three time w indows.Under the assumption of a Fermi-Dirac spectrum,the upper limits were found to be(5.4-7.0)×10^(9)cm^(2)for the three time windows.
文摘A search for the rare decays W^(+)→D_(s)^(+)γ and Z→D0γis performed using proton-proton collision data collected by the LHCb experiment at a centre-of-mass energy of 13TeV,corresponding to an integrated luminosity of 2.0fb−1.No significant signal is observed for either decay mode and upper limits on their branching fractions are set using W^(+)→D_(s)^(+)γ and Z→μ+μ−decays as normalization channels.The upper limits are 6.5×10^(−4) and 2.1×10^(−3) at 95% confidence level for the W^(+)→D_(s)^(+)γ and Z→D^(0)γ decay modes,respectively.This is the first reported search for the Z→D^(0)γ decay,while the upper limit on the W+→D+sγbranching fraction improves upon the previous best limit.
文摘In June 2024,the world’s first full high temperature superconducting(HTS)tokamak has successfully achieved its first plasma operation in Shanghai,China[1].This tokamak device,HH70,is designed by Energy Singularity Fusion Power Technology(Shanghai)Ltd.(ES Company)in Shanghai,China.The conceptual and engineering design of HH70 was initiated in June 2022,whose major radius(R_(0))and minor radius(a)are 0.7-0.75 m and 0.25-0.31 m,respectively.Its toroidal magnetic field B_(0)at R_(0)=0.7 m is 0.6 T,the total inductance of the tor-oidal field(TF)magnet are 6.48 H.Over the past two years,ES company has achieved the first milestone:suc-cessfully design,construct and operate an HTS tokamak,and has amassed experience and know‐how about such a first‐of‐its‐kind HTS device.The HH70 tokamak’s magnet system consists of three types of coils:central solenoid(CS)coil,poloidal field(PF)coil,and toroidal field(TF)coil,in which all of the coils are fabricated by HTS conductors.Hence,the HH70 is currently the first tokamak in the world to be fully integrated with HTS coils,marking a groundbreaking advancement in fusion technology.
基金Supported in part by the Ministry of Science and Technology of Chinathe U.S.Department of Energy,the Chinese Academy of Sciences,the CAS Center for Excellence in Particle Physics,the National Natural Science Foundation of China+3 种基金the Guangdong provincial governmentthe Shenzhen municipal government,the China General Nuclear Power Group,the Research Grants Council of the Hong Kong Special Administrative Region of China,the Ministry of Education in TWthe U.S.National Science Foundation,the Ministry of Education,Youth,and Sports of the Czech Republic,the Charles University Research Centre UNCE,the Joint Institute of Nuclear Research in Dubna,Russiathe National Commission of Scientific and Technological Research of Chile。
文摘The prediction of reactor antineutrino spectra will play a crucial role as reactor experiments enter the precision era.The positron energy spectrum of 3.5 million antineutrino inverse beta decay reactions observed by the Daya Bay experiment,in combination with the fission rates of fissile isotopes in the reactor,is used to extract the positron energy spectra resulting from the fission of specific isotopes.This information can be used to produce a precise,data-based prediction of the antineutrino energy spectrum in other reactor antineutrino experiments with different fission fractions than Daya Bay.The positron energy spectra are unfolded to obtain the antineutrino energy spectra by removing the contribution from detector response with the Wiener-SVD unfolding method.Consistent results are obtained with other unfolding methods.A technique to construct a data-based prediction of the reactor antineutrino energy spectrum is proposed and investigated.Given the reactor fission fractions,the technique can predict the energy spectrum to a 2%precision.In addition,we illustrate how to perform a rigorous comparison between the unfolded antineutrino spectrum and a theoretical model prediction that avoids the input model bias of the unfolding method.
基金supported by the National Key R&D Program of China(2024YFA1611401,2024YFA1611402,2024YFA1611403,and 2024YFA1611404)the National Natural Science Foundation of China(12393851,12393852,12393853,12393854,12205314,12105301,12305120,12261160362,12105294,U1931201,12375107,12275280,12105293,11905240,12375106,and 12261141691)+3 种基金Innovation Project of IHEP(E25451U2)Sichuan Province Science Foundation for Distinguished Young Scholars(2022JDJQ0043)the Youth Innovation Promotion Association of the Chinese Academy of Sciences(CAS YIPA)(2023019)the Institute of Plateau Meteorology,CMA Chengdu to maintain meteorological data,and Thailand’s National Science and Technology Development Agency(NSTDA)and National Research Council of Thailand(NRCT)under the High-Potential Research Team Grant Program(N42A650868)。
文摘We report the high-purity identification of cosmic-ray(CR)protons and a precise measurement of their energy spectrum from 0.15 to 12 PeV using the Large High Altitude Air Shower Observatory(LHAASO).Abundant event statistics,combined with the simultaneous detection of electrons/photons,muons,and Cherenkov light in air showers,enable spectroscopic measurements with statistical and systematic precision comparable to satellite data at lower energies.The proton spectrum shows significant hardening relative to low-energy extrapolations,culminating at 3 PeV,followed by sharp softening.This distinct spectral structure closely aligned with the knee in the all-particle spectrum points to the emergence of a new CR component at PeV energies that might be linked to the dozens of PeVatrons recently discovered by LHAASO,and offers crucial clues to the origin of Galactic cosmic rays.
