AerMet100 ultra-high strength steel plates with a thickness of 2 mm were welded using a COz laser welding system. The influences of the welding process parameters on the morphology and microstructure of the welding jo...AerMet100 ultra-high strength steel plates with a thickness of 2 mm were welded using a COz laser welding system. The influences of the welding process parameters on the morphology and microstructure of the welding joints were investigated, and the mechanical property of the welding joints was analyzed. The experimental results showed that the fusion zone of welding joint mainly consisted of columnar grains and a fine dendrite substructure grew epitaxially from the matrix. With the other conditions remaining unchanged, a finer weld microstructure was along with the scanning speed increase. The solidification microstructure gradually transformed from cellular crystal into dendrite crystal and the spaces of dendrite secondary arms rose from the fusion line to the center of the fusion zone. In the fusion zone of the weld, the rapid cooling caused the formation of martensite, which led the microhardness of the fusion zone higher than that of the matrix and the heat affected zone. The tensile strength of the welding joints was tested as 1 700 MPa, which was about 87% of the matrix. However, the tensile strength of the welding joints without defects existed was tested as 1832 MPa, which was about 94% of the matrix.展开更多
Carbon nauotube（ CNT） reinforced aluminum metal matrix composites were welded by electron beam welding and the microstructures of welded joints were investigated. The result showed that the interracial reaction happ...Carbon nauotube（ CNT） reinforced aluminum metal matrix composites were welded by electron beam welding and the microstructures of welded joints were investigated. The result showed that the interracial reaction happened between the CNTs and Al matrix, which resulted in producing brittle Al4 C3 compounds in electron beam welds. The extent of interfacial reaction varies gradually in the depth and width direction. The length of the reactants Al4C3 became short duo to the temperature gradient in the molten pool. The quantity and size of Al4 C3 compounds increased with the increase of beam current and the decrease of welding speed in the middle zone of weld. However, no needle-like phase Al4C3 was observed in HAZ.展开更多
基金Funded by the National Natural Science Foundation of China(Nos.51201087,51165038)the Project of Jiangxi Province of Education(No.GJJ13493)+1 种基金the State Key Laboratory of Solidification Processing in NWPU(No.SKLSP201306)the China Postdoctoral Science Foundation(No.2014M552485)
文摘AerMet100 ultra-high strength steel plates with a thickness of 2 mm were welded using a COz laser welding system. The influences of the welding process parameters on the morphology and microstructure of the welding joints were investigated, and the mechanical property of the welding joints was analyzed. The experimental results showed that the fusion zone of welding joint mainly consisted of columnar grains and a fine dendrite substructure grew epitaxially from the matrix. With the other conditions remaining unchanged, a finer weld microstructure was along with the scanning speed increase. The solidification microstructure gradually transformed from cellular crystal into dendrite crystal and the spaces of dendrite secondary arms rose from the fusion line to the center of the fusion zone. In the fusion zone of the weld, the rapid cooling caused the formation of martensite, which led the microhardness of the fusion zone higher than that of the matrix and the heat affected zone. The tensile strength of the welding joints was tested as 1 700 MPa, which was about 87% of the matrix. However, the tensile strength of the welding joints without defects existed was tested as 1832 MPa, which was about 94% of the matrix.
基金supported by the fund of Doctoral Startup Research of Nanchang Hangkong University(EA201203402)Aeronautical Science Foundation(20135456009)+1 种基金National Defense Key Disciplines Laboratory of Light Alloy Processing Science and Technology(gf201401003)State Key Laboratory of Solidification Processing in NWPU(SKLSP201412)
文摘Carbon nauotube（ CNT） reinforced aluminum metal matrix composites were welded by electron beam welding and the microstructures of welded joints were investigated. The result showed that the interracial reaction happened between the CNTs and Al matrix, which resulted in producing brittle Al4 C3 compounds in electron beam welds. The extent of interfacial reaction varies gradually in the depth and width direction. The length of the reactants Al4C3 became short duo to the temperature gradient in the molten pool. The quantity and size of Al4 C3 compounds increased with the increase of beam current and the decrease of welding speed in the middle zone of weld. However, no needle-like phase Al4C3 was observed in HAZ.
